When your feet get cold, your day on the ice is done.  If you want to extend your day so you have time to catch more fish, use these simple tricks to keep your feet warm.  First of all, in general, dress like it’s 15 degrees colder than actual temperature, from head to toe.  You can always take off too much clothes but it’s hard to add clothes you don’t have.  Remember, you are standing on a three foot thick block of ice.  If the wind is also blowing, that bites through you quick.  So try these tips for warm feet.

1. Double up socks and wear good boots.  Just because you can wear a pair of shoes for the walk to the mail box, don’t think these will stand the test of hours on the cold lake.  Get good quality thermal socks and double them up if you can fit them in your boots.
2. Wear your cold water waders.  If you think having your lower body wrapped in insulation is a good thing when standing in a flowing stream, take that out on the hardwater and you may never go back.
3. Put hot shots under your feet.  These are the little heater packs that give off heat for about 4 hours.  They may make it more uncomfortable to walk, but if your toes are warmer, that’s a good trade.
4. Use a 2 x 6 block of wood, under your feet.  Place this between your feet and the ice when you are sitting on your bucket or chair and it will act as an insulating barrier.  Cut a piece just short enough that it will fit in your ice fishing bucket and bring it with you.
5. Plastic bag your feet.  This old trick has been used to keep feet dry for decades.  It also keep them warm by not letting heat escape.

Keep your feet warm.  Fish longer!

An easy tip here to double your chances for catching fish while ice fishing.  Simple, use two lines.

In Canada you are allowed to use up to two lines in the water while ice fishing.  Two lures in the water will increase your chance of catching fish.  Does that mean you have to try to fish with a rod in each hand and two holes?  No, of course not.  What I like to do is drill two holes, at least 10 meters apart, and put a tip-up rig down one hole and set my bucket seat at the other with my jigging rod.

I always set myself up so that I am somewhat aligned with the bucket, the hole I am jigging in, and the tip up hole.  That way I can see the tip up hole without having to turn around.  If you are thinking ahead, on a breezy day, put the tip up down wind of you.  That way you have the wind at your back, making it easier to stay warm.

To make sure you comply with the fishing regulations, you have to keep both lines within 25 meters of you and within line of sight.  So if you are fishing in an ice shack or a pop-up shack, you need to leave a door open and the hole within the required 25 meters.

There are many styles of tip up equipment.  My new favorite is called a Jaw Jacker Hook Setter.  What I really like about this style is that when a fish is hooked, you still get to fish/retrieve the fish with a rod and reel.  Some tip up products require the line to be hand over hand retrieved which is just not the same.

When I go ice fishing I don’t have the luxury of having all the electronics and all the gear that can possibly be purchased for ice fishing, so I have learned how to adapt in a few ways.  One way is to use the reel on my ice fishing rods as depth finder.  Water depth is often an important piece of information when fishing and without a depth finder or a flasher, it can be hard to guess based on the amount of line you let loose from your spool.  But there is an easy way, simply use the amount of line spooled per turn of your crank handle to measure.

Finding out how much line your reel cranks in is easy.  I use 20 feet as the reference point.  To do this, I first get my measuring tape and layout 20 feet on my deck.

Then hook your lure in lightly at the beginning of your measuring tape.

Un-spool your line back to the 20 foot mark, then crank it back to the lure, counting the number of turns.  Divide 20 feet by the number of turns and you will know how many feet per turn of the crank handle.  Next time you are out fishing, drop your lure to the bottom, crank it up and do the math.

Do this for all your reels. The feet per turn of the crank will vary with the size of the spool as well as how much line you keep on your reel.  For my two reels, the amounts are 2 feet per turn

and 1.9 feet per turn.  So I just go by 2 feet per turn for both. I don’t often fish at depths beyond 20 feet so it’s a pretty quick and easy way to check the depth.

If I drill multiple holes, trying to find the drop off point of some structure, I can check the depth of each hole in 30 seconds or less.